Wyndham Grand Weifang, China
Zhuhai 2835led light belt consultation
by：EME LIGHTING
2021-03-22
The color temperature of LED light strips is very much now, and the color temperature is a professional concept. 2835led light strips are installed with LED light strips, which are generally fixed with 3M glue. Installed outdoors, often in wind and rain, over time will reduce the adhesiveness and cause the LED strip to fall off. Therefore, the outdoor installation often uses the card slot fixing method, and the places that need to be cut and connected are the same as the indoor installation. , It just needs to be equipped with waterproof glue to consolidate the waterproof effect of the connection point. Then use a special fixing clip to fix it, you can use an electric hammer to drill the eye, use a plastic expansion tube and screw to fix the clip
Simply speaking, it is the color of light. As far as white light is concerned, the color temperature is generally expressed in thousands of digits. The smaller the number, the yellower and more red the color, the larger the number, the whiter, and the more blue. The unit is expressed by K. . With good quality LED lamp beads, the brightness between the lamp beads and the lamp beads is consistent, and the light is uniform, and the brightness of the lamp strip should be consistent at the beginning and the end. 2835led light strip depends on the quality of FPC. FPC is divided into two types: copper and rolled copper. The copper foil of the copper-clad board is protruding. If you look closely, it can be seen from the connection between the pad and the FPC. The rolled copper is closely connected with the FPC and can be bent at will without the phenomenon of pad falling off. If the copper-clad board is bent too much, the pad will fall off. If the temperature is too high during maintenance, the pad will fall off. The light color of the light strip should also be the same. If the light has a uniform luminous effect, you must Choose good color rendering, color rendering index Ra>80 is a requirement that a professional LED strip must meet. This is also a requirement of the national standard GB50034-2013. The lighting factory is a high-tech LED lighting source company integrating the research and development of LED lamp beads. It provides you with free lighting solutions for different venues and on-site guidance and testing. The SMD5050 used in the 2835led lamp strip is packaged with Taiwan's high-brightness chip. The luminous flux is 1-2lm higher than ordinary chips. A 5050 lamp bead has three chips. When one chip is damaged, it will not affect the other two chips to emit light. When only three cores are damaged, only a group of three 5050s will not light, which will not affect the entire light strip. Years of industry experience, the company's complete process system, quality control, standardized implementation process, strict control cycle, and timely delivery.
Simply speaking, it is the color of light. As far as white light is concerned, the color temperature is generally expressed in thousands of digits. The smaller the number, the yellower and more red the color, the larger the number, the whiter, and the more blue. The unit is expressed by K. . With good quality LED lamp beads, the brightness between the lamp beads and the lamp beads is consistent, and the light is uniform, and the brightness of the lamp strip should be consistent at the beginning and the end. 2835led light strip depends on the quality of FPC. FPC is divided into two types: copper and rolled copper. The copper foil of the copper-clad board is protruding. If you look closely, it can be seen from the connection between the pad and the FPC. The rolled copper is closely connected with the FPC and can be bent at will without the phenomenon of pad falling off. If the copper-clad board is bent too much, the pad will fall off. If the temperature is too high during maintenance, the pad will fall off. The light color of the light strip should also be the same. If the light has a uniform luminous effect, you must Choose good color rendering, color rendering index Ra>80 is a requirement that a professional LED strip must meet. This is also a requirement of the national standard GB50034-2013. The lighting factory is a high-tech LED lighting source company integrating the research and development of LED lamp beads. It provides you with free lighting solutions for different venues and on-site guidance and testing. The SMD5050 used in the 2835led lamp strip is packaged with Taiwan's high-brightness chip. The luminous flux is 1-2lm higher than ordinary chips. A 5050 lamp bead has three chips. When one chip is damaged, it will not affect the other two chips to emit light. When only three cores are damaged, only a group of three 5050s will not light, which will not affect the entire light strip. Years of industry experience, the company's complete process system, quality control, standardized implementation process, strict control cycle, and timely delivery.
Custom message
Related Products
