How to buy and maintain floor lamps

by:EME LIGHTING     2021-03-22
Points for purchasing floor lamps, pay attention to the height of the ceiling-illuminated floor lamp; when purchasing the ceiling-illuminated floor lamp, consider the height of the ceiling and other factors. Take the 1.70m-1.80m high floor lamp as an example, the ceiling height is above 2.40m, and the effect is best. If the ceiling is too low, the light can only be concentrated in a local area, making people feel that the light is too bright and not soft enough. At the same time, using top-illuminated floor lamps, the ceiling in the home should preferably be white or light-colored, and the material of the ceiling should have a certain reflective effect. Pay attention to the luminosity of direct-illuminated floor lamps; pay attention to the purchase of direct-illuminated floor lamps. The lower edge of the lampshade is lower than the eyes, so that the eyes will not feel discomfort due to the light of the bulb. In addition, too much indoor light contrast will increase eye load, try to choose a floor lamp that can be dimmed. When in use, because the direct-illuminated light is concentrated, it is best to avoid mirrors and glass products near the reading position to avoid discomfort caused by reflections. Modeling floor lamps should pay attention to style; if you buy a 'modeling floor lampOf course, when purchasing this type of floor lamp, you must consider its consistency with the overall style of your home. For example, a noble classic standing lamp made of heavy blood-flower stone is totally different from modern furniture with a streamlined style in Yuppie style. Floor lamp installation method 1. Preparation before installation. Before installation, carefully read the installation drawings and the product manual of the floor lamp, and prepare common tools for lamp installation, such as flat-headed Phillips screwdrivers, hammers, etc. After unpacking the parts, please do not confuse them. If there are many similar parts, the installation drawings will generally draw a comparison chart of actual size, and the unused parts are crossed, which is very easy to distinguish the various parts. 2. Check before installation. Check the accessories of the floor lamp and other conditions before installation. If you find that the floor lamp board is damaged, you can contact the merchant for replacement. Where the screws, eccentric parts, and wooden shafts are to be installed, the guide holes will be opened, so there is no need to worry about the positioning of the parts. It should be noted that the wrong parts should not be screwed together repeatedly, otherwise the board will be easily damaged, and the installation will often cause instability and tilt. 3. Installing the floor lamp. Generally, the floor lamp should have a cast iron chassis, which is slightly smaller than the surface base. The black plastic cap should be the fastener used to fix the lampshade. The order of parts from bottom to top should be: chassis fastening nut, Cast iron chassis, base, lamp pole, lamp holder, lampshade, plastic fasteners, bulbs. The power cord coming out of the floor lamp pole passes through the fastening nut of the chassis, the cast iron chassis, and the base, and then connects to the power cord and wraps it with electrical tape. The chassis should have a recess to extend the power cord. The floor lamp here reminds everyone that the power cord of the floor lamp must be handled properly. One is the safety of electricity, and the other is that it is not easy to trip people when walking around in the home. Floor lamp maintenance tips: 1. Moisture-proof electrical appliances are most worried about moisture, which will reduce the service life and be dangerous to electricity. Therefore, the key step in floor lamp maintenance is to prevent moisture, whether it is placed in the living room, or in the bathroom or bathroom. For lighting and kitchen stove headlights, moisture-proof lampshades must be installed to prevent moisture intrusion and promote rust damage or leakage short circuits on the lamps and lanterns. 2. Dust removal floor lamp maintenance must often be done with dust, especially the lampshade of the floor lamp. The lampshade is easy to accumulate ash layer and cause darkening, which affects the lighting effect, so it should be cleaned frequently. When cleaning the lampshade of the floor lamp, use a clean feather duster to gently sweep away the dust, so as not to deform the lampshade. There are several situations for floor lamp dust removal and wiping: (1) For normal cleaning, use a clean feather duster to gently dust off. Be very careful. (2) If it is a non-metal floor lamp, it can be wiped clean with a damp cloth. Be careful not to wipe the power cord. (3) If it is a metal lamp, wipe it with a dry cloth, don't touch it with water. Note: When cleaning and maintenance, disconnect the connected power supply first, and at the same time, be careful not to change the structure of the lighting, and do not change the parts of the lighting randomly. After the cleaning and maintenance, the lighting should be installed as it is, and do not miss or install it incorrectly. Lighting parts, so as not to cause danger. At the same time, do not clean the lamp with water as much as possible, just wipe it with a dry cloth dampened with water. If you accidentally touch the water, try to wipe it dry as much as possible. Do not wipe it with a wet cloth immediately after turning on the light. 3. Don't switch frequently. Try not to switch frequently when using the lighting, because the current through the filament is greater than the current during normal operation when the lighting is frequently started, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its use. Life, this is also a point that should be paid attention to in all lighting maintenance.
Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...