Installation of decorate condole carries on the crystal droplight process and common problems

Decorate modern crystal chandelier droplight is one of the ceiling lamp, it is made of crystal droplight to decorate condole top is installed on the ceiling, so called decorate condole carries on the crystal droplight, decorate condole carries on the design of crystal droplight appearance design beautiful generous, elegant classical style, strong and durable, suitable for modern furniture, luxury villas, business club, quick hotel and hotel restaurant space decoration design of lamps and lanterns, highlighting the elegant taste. Decorate condole carries on the crystal droplight on stateroom, supplement, for in the style of the decoration has draw the dragon point clear effect, generally stateroom, can adopt the crystal droplight, suction a top pick its cause is now stateroom ratio is limited, selection of crystal droplight is relatively higher, suction a top can give all indoor decorate a style to create more decoration design. On the light source, usually a bottom piezoelectric light bulbs, led energy-saving lamps and led crystal droplight, generally the forehead is full of more focus on the led light source, due to the light source is attributable to the new environmental protection light source, application is more convenient. On the selection, as far as possible to choose the suitable own home interior decoration style. Installation of decorate condole carries on the crystal droplight process and common problems ( 1) When diamond structure installed in the ceiling lamp, should choose the embedded bolt, or use the expansion screws, polyester plastic plug plug or fixed; Cannot be applied wedge. Described and the bearing capacity of the clamp should be consistent with the sitting room to absorb dome light net weight. To ensure that the sitting room to absorb dome light fixed solid,, and can prolong its life. ( 2) Elected by expansion screws fixed, the goods according to the technical standard of choosing bolt specification, the punch diameter and laid the deep to be consistent with bolt specification. ( 3) Fixed socket bolts in the total number of not less than the perforation, fixed on the base of lamps and lanterns and anchor bolt diameter should match with diameter; Base on the lamps and lanterns of no fixed installation hole ( When installing independent open hole) , each of the lamps and lanterns to fixed anchor bolts or screws shall not less than two, and the focus point of lamps and lanterns to the anchor bolts or screws to coincide with the center of gravity point; Only when the diameter of the insulation stage in 75 mm and the following, only can choose a anchor bolt or screw stationary. ( 4) Sitting room dome light don't installed on flammable items immediately, some in the home in order to better the beauty is generous with three splint after the paint line in the living room behind absorb dome light, in fact it is very dangerous, be sure to use heat insulation heat preservation measures; When if the surface temperature of lamps and lanterns location near flammable, adopt heat insulation or heat rejection measures. ( 5) Absorb dome light before installation should also examine: (1) to each of the lamps and lanterns of transmission lines core cross section, the copper wire is not less than 0. 4 was, copper is not less than 0. 5 was, or fuses must be replaced. (2) the wire connection with lamp holder and lamp holder parallel wire connection between wants firm, electric contact should be good, in order to avoid because of the poor contact, produce sparks between wire and terminal, and dangerous. ( 6) If absorb dome light is used in the screw base, its connection also note the following two points: (1) phase line on the center of contact terminals, they can zero line up on the thread of the terminal; (2) the lamp holder of the insulation shell should not have broken and the leakage, to prevent electric shock when replacement bulbs. ( 7) Equipped with incandescent light bulb absorb dome light, the light bulb should not be close to the chimney; Bulb of power also should choose according to the requirements of product technology, not too big, in order to avoid the light bulb temperature is exorbitant, after the glass broken down splashed down cuts. ( 8) To absorb dome light power into the line connecting the two threads, electric contact should be good, still wrapped in black tape, respectively, and keep a certain distance, if possible try not to put the two threads in the same piece of sheet metal, in order to avoid short circuit, produce risk.